Ningbo Changfeng Mechanical Factory
Ningbo Changfeng Mechanical Factory
Gold Verified Supplier
2Yrs
Verified Business License Business License
Main Products: many kinds of mechanical engineering solutions, OEM casting service, forged components supplier, sheet metal stamping supplier
Home > Blog > Casting Defects Explained: Shrinkage, Cold Shut and Porosity

Contact Us

Mrs. JADE
Chat Now

Your inquiry content must be between 10 to 5000 characters

Please enter Your valid email address

Please enter a correct verification code.

Casting Defects Explained: Shrinkage, Cold Shut and Porosity

Three castings arrived at a machine shop in the same delivery, and each failed in a different way. One leaked after the flange was faced, one broke along a line that looked like a fold, and one showed a cluster of round holes when a bore was opened. All three were called porosity on the rejection note, and two of those calls were wrong.

Casting shrinkage defects, a cold shut casting defect and gas porosity in castings are three different faults with three different causes. They look similar on a fracture and they are cured by opposite changes to the process, which is why a foundry that treats them as one problem fixes none of them.

The notes below separate the three families, give the inspection that identifies each, and show where the cure sits in the gating, the pour and the mould.

1. Casting Shrinkage Defects: Where the Metal Goes When It Cools

Every metal shrinks as it solidifies, and a casting that cannot be fed with liquid metal while it does will hold a void. Casting shrinkage defects are therefore a feeding problem first and a pouring problem second, and they appear in the section that solidified last.

The defect has two forms. A open cavity at a riser top is a shrinkage pipe and it is visible, while a cavity closed inside the wall is a shrinkage porosity and it is not. The second is the one that survives a visual check and fails a pressure test.

Position tells the story. Casting shrinkage defects sit at a hot spot, which is any junction where two sections meet and the sand is surrounded by metal on several sides. A T junction, a boss on a plate and the centre of a heavy flange are the usual locations.

2. Cold Shut Casting Defect: The Line That Looks Like a Crack

A cold shut casting defect forms when two streams of metal meet and fail to fuse, so the casting carries a line that is a fold rather than a fracture. The line has rounded edges under magnification, and that rounded edge is what separates it from a hot tear.

The cause is temperature at the meeting point. The metal has lost enough heat that the two fronts freeze on contact, and the oxide on each surface stays between them as a film that no amount of pressure will break.

Ningbo Changfeng Mechanical Factory checks the meeting point on the pattern before the first pour, since a cold shut casting defect is decided by the layout rather than by the ladle. Geometry drives it. A thin section between two heavy ones, a long flow path around a core and a gate that enters on one side of a symmetrical part all ask two fronts to meet far from the source of hot metal, and that meeting point is where the line appears.

3. Gas Porosity in Castings: Round Holes in a Straight Wall

Gas porosity in castings appears as round or slightly elongated holes with smooth internal surfaces, often clustered near a surface or at the top of a section. The shape is the clue, because a gas bubble is spherical until the surrounding metal traps it.

The gas comes from three places: moisture in the sand, hydrogen dissolved in the melt, and air trapped by a gating system that plunges rather than fills smoothly. Each leaves a similar mark and each needs a different correction.

Gas porosity in castings tends to sit where the metal was last to freeze, but unlike shrinkage it can also appear in a thin wall that froze early, because a bubble that formed at the gate has no time to escape through a thin section.

4. Reading a Casting Defect: Shrinkage Versus Gas

The single most useful test is a fracture. A shrinkage cavity has a rough, dendritic interior with visible branches, while a gas hole has a smooth, rounded interior that reflects light. Break the part open and the argument usually ends.

The second test is position relative to the thermal centre. A defect at the heaviest section that solidified last is shrinkage, and a defect distributed through a wall at random is more likely gas.

The third test is response to a process change. Reduce the pouring temperature and gas porosity improves while shrinkage can worsen, because colder metal needs more feeding; the direction the defect moves tells you which family you are fighting.

5. Sand Inclusion and Slag in Casting Defects

A sand inclusion is a piece of mould material that has been washed into the metal and trapped, and it shows as an irregular dark body with a friable texture. A slag inclusion is a similar shape with a glassy look and it comes from the ladle rather than the mould.

Changfeng Mechanical reads a black speck in a machined face as a pouring fault until the section proves otherwise, because sand and slag both enter through the gate rather than through the metal. Both are gating faults rather than metal faults. A gate that directs the stream at a sand wall erodes it, and a pouring basin that does not trap the first metal lets slag travel into the cavity.

Both are also found late, because they sit below the surface and appear when a bore or a face is cut. A machine shop that sees a black speck in a machined face is looking at a defect that was poured weeks earlier.

6. Hot Tear: A Casting Defect With a Grain Boundary Cause

A hot tear is a crack that opens while the casting is still partly liquid, and it runs along the grain boundaries rather than across them. It appears at a change of section where the metal contracts against a mould that will not move.

The cause is restraint. A casting with a heavy flange and a thin web will tear at the junction because the thin web cools first and the flange then pulls against it, and a mould that is too strong adds to the load.

The cure is a radius and a slower cooling rather than a hotter pour. A fillet that spreads the strain and a mould that yields slightly will remove a hot tear that a temperature change would merely move.

7. Gating and Riser Design Against a Casting Defect

Most casting defects are decided before the metal is poured, in the layout of gates and risers. A riser placed on the heavy section feeds it, and a gate that fills the cavity from the bottom up keeps the metal calm and the sand in place.

The pouring temperature is the second lever. Hotter metal fills a thin section and lets gas escape, and it also increases shrinkage and grain size, so the temperature is a balance rather than a maximum.

At Ningbo Changfeng Mechanical Factory the gating layout is reviewed against the last defect record before a pattern is released, because a defect that has appeared once in a family of parts will appear again in the next size up. The record is what turns a scrap into a design change.

8. Casting Shrinkage Defects in Heavy Sections

A heavy section needs a riser that stays liquid longer than the section it feeds, which means a riser with a larger modulus and often an exothermic sleeve. A riser that freezes at the same time as the casting does nothing except add weight.

Chills are the other tool. A steel or graphite chill set into the mould at a heavy junction speeds the local cooling and moves the last point to solidify toward the riser, which converts a scattered shrinkage into a single pipe that can be cut off.

The table below maps the three main families against their appearance, their usual location and the correction that removes them. It is written for the bench rather than for a textbook, so the entries are what a setter or an inspector can see.

DefectAppearanceUsual locationCorrection
Casting shrinkage defectsRough dendritic interior, cavity or spongeHot spot at a junction or heavy flangeLarger riser, chill, graded wall
Cold shut casting defectRounded fold line, no brightnessThin section between two heavy onesHotter pour, extra gate, shorter flow path
Gas porosity in castingsRound smooth holes, often clusteredLast area to freeze, or under a skinDry sand, degassed melt, calmer fill
Sand inclusionIrregular dark body, friableFacing the gate, inside a boreSofter gating, better sand strength
Hot tearIntergranular crack, oxidised facesSection change under restraintRadius, yielding mould, slower cooling

9. Inspection Methods for Gas Porosity and Shrinkage

Ningbo Changfeng Mechanical films a first article before the run is released, and the film is read for shape first because gas porosity in castings and shrinkage look alike at a glance. Radiography finds both families and separates them by shape, which is why a film is read for shape before it is read for size. A cluster of round images is gas, and an irregular dark region at a heavy junction is shrinkage.

Dye penetrant finds what reaches a surface and nothing else, so a penetrant test that passes says little about the wall behind it. Ultrasonic testing reaches deeper and needs a flat entry surface and a trained operator to interpret the trace.

Sectioning settles the argument. Cutting a first article through the critical section and polishing the face shows the internal structure at a scale no film can match, and it is the least expensive way to prove a gating change worked.

10. Frequently Asked Questions

10.1 How can I tell casting shrinkage defects from gas porosity?

Break the part open and look at the interior surface. A shrinkage cavity is rough and dendritic with visible branches, while a gas hole is smooth and rounded and reflects light. Position confirms it, since shrinkage sits at the heaviest section that froze last while gas can appear anywhere the metal trapped a bubble. A radiograph read for shape gives the same answer without destroying the part, and the fracture test belongs on a scrap piece rather than on a finished part that a customer may still see.

10.2 What causes a cold shut casting defect on a thin wall?

Two metal fronts meeting after both have lost enough heat to freeze on contact, which leaves an oxide film between them. It appears on a thin section between two heavy ones, at the end of a long flow path, or where a single gate feeds a symmetrical part from one side. A hotter pour, an extra gate or a shorter path removes it, and polishing the line will not. A setter who sees the line on the first box should stop and check the pouring temperature before running the rest of the order.

10.3 Can gas porosity in castings be welded after machining?

It can be repaired when the hole is exposed and the repair is small, using a qualified procedure with a preheat matched to the material. The risk is that a welded area hides a second cluster nearby that the weld does not reach, so the part is usually re-tested after repair rather than returned to the line. On a pressure boundary many specifications refuse the repair outright. The decision belongs to the drawing, which should say whether a weld is permitted and at what size, rather than to a conversation after the bore is opened.

10.4 Which defect is worse for a machined casting?

A subsurface defect is worse than a visible one, because it survives every check until a cutter opens it. A shrinkage cavity below a flange face or a sand inclusion inside a bore appears after most of the machining hours are already spent, which turns a material fault into a full value loss. That is why radiography is done before the first cut on a critical casting. A defect found in the rough state costs a casting, and the same defect found after machining costs the casting plus the hours already spent on it.

Share

Contact Us

Send Inquiry to Us
* Message
0/5000

Want the best price? Post an RFQ now!

Recommended Products