What Are Casting Parts? Sand, Investment and Die Cast Routes
A casting is a part shaped by pouring liquid metal into a cavity. Three routes do that in three different ways: green sand uses a pattern and a mould that is broken after each pour, investment uses a wax pattern coated in ceramic that is burnt out and replaced by metal, and die casting uses a steel tool that opens and closes for tens of thousands of cycles.
The three are not interchangeable at the drawing stage. Each one fixes a tolerance band, a minimum wall, a surface finish and a tooling bill, and a part drawn for one route quoted on another usually comes back with a price that reflects the mismatch rather than the geometry.
The notes below explain what casting parts process routes commit a buyer to, and give the numbers that decide between them on a real drawing.
1. What Casting Parts Have in Common
Every casting starts with three things: a cavity, a metal that fills it, and a shrink allowance carried by the pattern or the die. Common irons, steels, aluminium and brass contract by roughly 1.0 to 2.1 percent as they solidify, so the tool is made oversize by that amount and the drawing stays at nominal.
Three defects are common to all routes. Shrinkage appears where a heavy section feeds a thin one, gas porosity comes from trapped air or from moisture in the mould, and inclusions come from a mould face that broke down under the pour. The route changes how easily each is controlled, not whether it exists.
What truly separates the casting parts process routes is the mould material and how many times the tool survives. That single difference drives tolerance, finish, minimum wall, tooling cost and the lot size at which the route makes sense.
2. Casting Parts Process Routes: Three Ways to Fill a Mould
Green sand is the oldest and the most flexible. A pattern is packed in sand bonded with clay or resin, the mould is closed, metal is poured, and the sand is knocked out and reused. Tooling is cheap, lead time is short, and the process accepts large parts and internal cavities formed by cores.
Investment casting builds the mould around the part instead of around a pattern. Wax is injected into a metal die, assembled onto a tree, dipped in ceramic slurry five to eight times, and fired so the wax leaves and the shell hardens. The shell is broken away after the pour, which is why investment casting components hold thin walls and fine detail.
Die casting forces metal into a hardened steel die under pressure. The die is expensive and the cycle is fast, which pushes the route towards high volume in aluminium, zinc or magnesium. Porosity is the standing risk, since gas trapped during the shot forms voids that appear when the part is machined.
A fourth family sits between the three casting parts process routes: gravity and low pressure permanent mould casting, where a reusable metal mould is filled without the high velocity of a die casting. It suits medium volume in aluminium with better soundness than a die casting and better tolerance than sand.
3. Sand Casting Parts Tolerance: The Plus or Minus That Fits
Sand casting parts tolerance is expressed as a grade rather than as a single figure, because the band grows with the dimension. ISO 8062 is the usual reference, and green sand typically lands at CT10 to CT13 while a resin-bonded or no-bake mould reaches CT9 to CT11.
In practical terms sand casting parts tolerance grows with the dimension: a 100 mm feature at CT10 carries roughly 1.4 mm of total tolerance, while the same dimension at CT13 carries about 4 mm. Asking a green sand foundry for CT7 does not improve the mould; it moves the work to a machining centre, where the same feature is cut at plus or minus 0.05 mm for less money.
Three drawing features decide whether the band is achievable. Draft of 1 to 2 degrees per side lets the pattern leave the sand. Fillets at internal corners spread the thermal load and reduce hot tearing. A machining allowance of 3 to 5 mm on faces that will be cut leaves enough stock to clean up without adding weight everywhere else.
4. Investment Casting Components: Where the Cost Goes
Investment casting components are priced by the shell rather than by the metal. Each part carries the cost of a wax pattern, several ceramic coats, a firing cycle and a cut-off step, and those costs fall per piece as the tree gets denser.
For investment casting components the route holds tolerance grades around CT4 to CT6, walls down to about 1.5 mm on small parts, and a surface around Ra 3.2 to 6.3 micrometres. Draft can be as little as 0.5 degrees, which is why the route suits levers, impellers, linkage parts and thin stainless housings that sand cannot hold.
Alloy range is the other reason buyers choose investment casting components. Carbon and stainless steels, nickel and cobalt alloys all cast in the same shell line, so a 17-4PH or CF8M part needs no separate process development. The limit is size: most shops work comfortably up to a few kilograms per piece, and heavier parts move to sand.
Cost control comes down to tree design. A wax assembly that carries forty small parts per tree spreads the shell cost across forty pieces, while the same parts cast one per tree pay the full shell cost each. At Ningbo Changfeng Mechanical Factory the quote for an investment part always states pieces per tree, because that number moves the price more than the alloy does.
5. Die Casting Parts: Volume, Draft and Porosity
Die casting trades tooling cost for piece price and tolerance. A hardened steel die running aluminium holds walls around 1.5 mm, draft of 1 to 3 degrees, and tolerances set by the die casting product standards rather than by ISO 8062.
Porosity is the constraint that shapes design. Gas trapped during the shot, and shrinkage at heavy sections, produce voids that show up as bubbles when a boss is drilled or a flange is faced. Vacuum assistance, squeeze pins and a redesigned gate reduce it, and none of them removes it entirely.
Tooling is the entry ticket. A die for a moderate aluminium housing often runs into five figures in US dollars, with a life of perhaps a hundred thousand shots before refurbishment. That arithmetic sets a floor on annual volume, and it is the reason a part at 800 pieces a year rarely belongs in a die.
Post-processing is part of the route. Trimming the gate and overflow, machining the sealing faces, and impregnating a body that must hold pressure are all steps a die casting buyer pays for, and all of them are cheaper to plan at the drawing stage than to add later. Ningbo Changfeng Mechanical prices those steps separately so a buyer can see which ones the design could remove.
6. Comparing the Three Casting Routes
The table sets the three routes against the numbers a buyer has to commit to, including sand casting parts tolerance, before a quote can be compared.
| Route | Tolerance grade | Minimum wall | Surface | Tooling | Typical lot |
|---|---|---|---|---|---|
| Green sand | CT10 to CT13 | 3 to 4 mm | Ra 12.5 to 25 micrometre | Low, pattern and boxes | 50 to 5,000 per year |
| Resin bonded sand | CT9 to CT11 | 3 mm | Ra 6.3 to 12.5 micrometre | Low to moderate | 100 to 5,000 per year |
| Investment | CT4 to CT6 | 1.5 mm | Ra 3.2 to 6.3 micrometre | Moderate, wax die | 500 to 50,000 per year |
| Die casting | Die standard, tighter than CT7 | 1.5 mm aluminium | Ra 1.6 to 3.2 micrometre | High, hardened die | 20,000 and above |
7. Choosing a Casting Parts Process Route by the Numbers
Comparing casting parts process routes on a drawing comes down to an amortisation, not a preference. Divide the tooling cost by the annual volume and add the result to the piece price, then compare the totals over the life of the programme rather than over the first order.
A useful first pass: below about 3,000 pieces a year, sand wins on total cost unless the geometry is impossible. Between 3,000 and 15,000, investment wins where the walls are thin or the tolerance is tight. Above 15,000, a die usually pays for itself inside two years, provided the design will not change.
Geometry carries a veto over the arithmetic. An internal cavity that needs a core, an undercut that needs a slide, or a part heavier than a few kilograms can remove a route from the table whatever the volume says. Secondary machining often decides the rest, since a route that casts a face within 0.3 mm saves a milling step on every piece. That is where sand casting parts tolerance earns its keep, on faces that will never be machined.
8. A Case: Moving 800 Casting Parts Off the Die Route
A pump bracket, 180 by 120 by 40 mm with a 4 mm wall, was quoted both ways at 800 pieces a year. The die casting quote carried a tool at 52,000 dollars and a piece price of 6.80, with a machining step at 2.00. The sand quote carried a pattern at 1,800 and a piece price of 11.20, with the same machining step.
Over three years the die route totalled 52,000 plus 3 years of 800 pieces at 8.80, which is about 73,000. The sand route totalled 1,800 plus 3 years of 800 pieces at 13.20, which is about 33,500. The cheaper piece price lost by a wide margin once the tool was carried.
Two design changes made sand work. The wall went from 4 to 5 mm, which removed a feeding problem at the boss, and two small holes moved from the casting to the drilling step, where they cost a few seconds. Weight rose by about 6 percent, which the application accepted.
The bracket stayed in sand until the volume tripled, at which point a die became the cheaper route on the same arithmetic. Changfeng Mechanical keeps both quotes on file for that reason, since a route decision has a volume at which it reverses.
9. Drawing Notes That Keep a Casting Parts Quote Low
State a tolerance grade, not a set of plus or minus figures on every dimension. A note reading CT10 to ISO 8062 tells a foundry what the mould has to achieve, while twenty tight dimensions on as-cast faces tell it that the buyer has not chosen a route yet.
Put draft and fillets on the model rather than in a note. A model without draft forces the foundry to add it, and the added draft moves faces that other features are toleranced against. Datums belong on machined faces, so the as-cast surfaces do not become the reference for a machined hole.
Ask for radiography where the section carries pressure or fatigue. A blanket requirement on the whole casting adds cost to every piece and finds defects in places where they do not matter. At Changfeng Mechanical Factory that request is answered with a zone map rather than a yes or no.
10. Frequently Asked Questions on Casting Parts Process Routes
10.1 Is a casting cheaper than a machined part?
It depends on the shape and the volume. A part that removes most of its stock as swarf is usually cheaper as a casting, because both the metal and the cutting time are paid for and then thrown away. A simple round part in small quantity is cheaper from bar, where no tooling is needed, the tolerance comes free and the cut is quick. Compare the two over the life of the programme and price the same secondary machining on each side, since a casting that arrives near net shape saves an operation that bar stock cannot.
10.2 How tight can sand casting parts tolerance be held?
CT9 is realistic from a good resin-bonded mould, and CT10 to CT11 is normal for green sand on a part of moderate size. Tighter than that is possible on a single critical dimension with a jig, and it is not a route capability. The practical move is to cast at CT10 and machine the two faces that matter, which costs less than chasing a grade the mould cannot repeat. When a buyer insists on CT7 across a whole part, the quote usually returns with full inspection added, and that inspection finds what a machining cut would have removed.
10.3 What wall thickness can investment casting components hold?
About 1.5 mm on small parts, with 0.8 mm achievable over a short run on a small area if the alloy flows well. Below that the shell becomes fragile and the pour may freeze before the section fills. A thin wall also needs a generous fillet at the junction, because a sharp internal corner in a thin section is where a hot tear starts. Wall thickness belongs in the quote discussion, since a 0.3 mm reduction can move a design out of investment casting components and into a pressing.
10.4 Why does a die casting show porosity after machining?
Because the gas or shrinkage void was already inside the wall and the cut opened it. Machining removes the dense skin that sealed the surface, so a void a millimetre below appears as a bubble on the new face. Vacuum assistance, a better gate position and a thicker section at the machined face all reduce the risk. A pressure test on the finished part remains the check that matters, and a leak specification in the purchase order is what turns that check into an acceptance criterion.
Recently Posted
-
Brass Parts Surface Finishing: From As-Machined to Nickel Plated
November 16, 2026A box of brass fittings arrived with a finish the buyer had not asked for and did not want. Half the parts were bright and half we
Read More -
What Are Brass Parts? Alloy Families and Machined Component Basics
November 16, 2026A shipment of 2,400 machined brass fittings reached a customer in northern Europe and came back six weeks later with a 3 percent l
Read More